Skip to main content

National Fuel Geyser Awareness

Fuel Geyser Triangle with Fuel, Heat, and Pressure as the sides.

Click Here to Report Fuel Geyser Incidents

 

What is a fuel geyser?

The rapid and energetic expulsion of heated fuel in a closed container when a fuel container is quickly depressurized. Heat and agitation causes the pressure increase. A delayed fuel geyser can occur after the fuel container is opened.

 

 

What does a fuel geyser look like?

Why is this important to me?

Over the last two years three significant burn injuries have occurred on prescribed fire and wildland fire incidents. Many additional fuel geyser incidents have been reported. These events happen frequently and have the potential to harm users of power equipment and people refueling power equipment. If you experience or have experienced a fuel geyser please report it.

Incident Reports

The following reports contain incidents where fuel geysers have occurred:

What do I need to know to protect myself?

Fuel geysers can happen anytime when there is fuel, heat & pressure from small gasoline-powered engines, chainsaws, leaf blowers, portable pumps, even when opening fuel transport containers.

Fuel geysers have resulted in injury when sprayed fuel and vapor ignite.

Appropriate precautions when there is fuel, heat & pressure, may prevent significant burns in the event of fuel spray.

  • Always assume fuel tanks and fuel containers are pressurized.
  • Ensure the cap is correctly secured.
  • Always check fuel levels before opening the fuel tank or filler cap. Fuel levels greater than ½ tank may geyser.
  • Move at least 20 feet or more from any heat source. 
  • For safety cans with pour spouts, direct potential spray away.
  • Cover the cap with a rag to contain potential fuel geyser spray.
  • Be extra vigilant when equipment is running poorly with fuel levels above ½ tank.
  • Start the saw at least 10 feet from the fueling area.
  • Do not use fuel older than one month.

If the equipment is running poorly or vapor lock is suspected:

  1. Do not open fuel cap. Relieving the pressure does not alleviate a “vapor lock” equipment.
  2. Check fuel level through the tank or use the bar oil level to gage fuel level.
  3. If fuel level is over ½ full, DO NOT open the tank.
  4. Allow the equipment to thoroughly cool. This could take over 45 minutes.
  5. When the equipment is cool, restart the equipment.

It’s YOUR job to protect yourself and others. Know how to handle your equipment to avoid fuel geysers anytime there is fuel, heat & pressure.

What should I do If I experience a fuel geyser?

Please REPORT every fuel geyser incident you experience!

The information you provide our engineers can mean the difference between one of our employees getting injured or not.

To report an incident go to Fuel Geyser Incident Reporting Form.

Location of Incidents

View a map of fuel geysering incidents and fuel requirements.

Videos

Video: USFS - Fuel Geysering: Predictable?

 

 

NWCG Latest Announcements

EMC Memo 25-001: Interim Rapid Extraction Module (REMS) Training and Qualification Requirements

Date: June 3, 2025
Questions?  Please contact:
Emergency Medical Committee

The Emergency Medical Committee has issued interim guidance for Rapid Extraction Module Support (REMS) teams. Until further notice, Type I and II REMS teams must designate a team leader qualified at Firefighter Type 1 Squad Boss (FFT1) or higher. This temporary change replaces the Single Resource Boss (SRB) requirement, which is currently not feasible due to administrative barriers.

This memorandum does not include any other changes to the NWCG Standards for Rapid Extraction Module Support, PMS 552. This interim change takes effect immediately and will remain in place until further notice.

References:

EMC Memo 25-001: Interim Rapid Extraction Module (REMS) Training and Qualification Requirements

NWCG Standards for Rapid Extraction Module Support, PMS 552

Equipment Bulletin 25-002: Chaps, Chain Saw, M-2020, Nonconformities Affecting Use, Appearance, and Serviceability

Date: June 2, 2025
Questions?  Please contact:
Equipment Technology Committee

The Equipment Technology Committee issued Equipment Bulletin: 25-002 to address a manufacturing nonconformity affecting Forest Service specification, 6170-4K Chain Saw Chaps. The issue applies to chaps manufactured in 2024 and 2025 and distributed through FedMall. These chaps may have incorrectly bound edges that expose inner protective layers.

Independent purchasers should inspect all chain saw chaps received from FedMall beginning in 2024, prior to use. Review the full Equipment Bulletin: 25-002 for inspection criteria and recommended actions.

References:

NWCG Alerts

ETC Equipment Bulletin: 25-002

2024 Wildland Fire Emergency Medical Service Awards

Date: May 22, 2025
Questions?  Please contact:
Emergency Medical Committee

The NWCG Emergency Medical Committee (EMC) is proud to announce the recipients of the 2024 Wildland Fire Emergency Medical Service Awards. Each year, EMC recognizes individuals and groups who have demonstrated exceptional actions or accomplishments that go above and beyond their normal mission or job duties.

Congratulations to all the awardees and nominees. Through leadership and initiative, they have made significant contributions to the safety and well-being of the wildland fire community. These honors are well deserved.

References:

2024 Wildland Fire EMS Awards

NWCG Emergency Medical Committee

NWCG Welcomes the Incident Management Teams Association as an Associate Member

Date: May 21, 2025
Questions?  Please contact:
https://www.nwcg.gov/contact-us

The NWCG Executive Board is honored to announce that the Incident Management Teams Association (IMTA) has joined the National Wildfire Coordinating Group as an associate member.

IMTA is a dedicated group of incident management professionals committed to enhancing the profession by promoting standards and fostering collaboration across federal, state, local, Tribal, and private sector partners throughout all phases of incident management.

“Joining NWCG aligns with our mission to elevate incident management professionals nationwide,” said Dr. Randal Collins, President of IMTA. “This is a proud moment for all of us committed to advancing public safety.”

References:

Incident Management Teams Association

National Wildfire Coordinating Group