Skip to main content

PMS 448

Heater – Propane, Outdoor, 360° Radiant Heat

NFES #
006187
Category
Camp
Updated
Storage and Shelf Life Checks
None

Initial Inspection/Disposal Criteria

  1. Visual inspect for missing parts (guards, knobs, etc.) or any structural damage preventing repair. Inspect for torn or cut heater element, damaged or cracked hose/hose connections, loose fittings, and damage to regulators.
  2. Inspect hoses for cracks, inspecting for breaks by flexing.
  3. Inspect hose or valve for foreign material that might cause a blocked line.
  4. Inspect O-rings on supply hose and replace if needed.
  5. Inspect for out-of-round fittings by screwing regulator into tank POL fitting.
  6. Return to stock if item passes initial inspection, passes Testing for Performance, is clean, and is serviceable.
  7. Refurbish heater if any damage is repairable, missing or damaged components are available, and it’s economically feasible to refurbish.
  8. Dispose of heaters that have structural damage that prevents repair. Salvage parts that are serviceable for future repairs. Dispose of damaged regulators and cracked or damaged hoses.
  9. Ensure the heater is equipped with a SAFETY TIP-OVER SWITCH (SEE ATTACHMENT).
  10. If not equipped with SAFETY TIP-OVER SWITCH remove from service.

Refurbishing Procedures

A. Cleaning

  1. Clean the outside of the heater using a damp cloth. DO NOT clean the heater by spraying water on it.
  2. Clean the inside of the heater using compressed air.

B. Repair

  1. Replace regulator if there is any damage to the regulator or threads do not properly seat.
  2. Replace or straighten any damaged or bent parts.
  3. Repair or replace auto shut off valve if not working properly (if applicable.)
  4. Replace any damaged or cracked hose or hose connections.

C. Testing for Performance

  1. Prior to testing use an air hose to blow unit off of any dust, dirt or debris.
  2. Perform initial inspections prior to testing.
  3. Ensure a fire extinguisher is in the work area prior to lighting any heater.
  4. Mount or connect the heater to a LP-Gas supply cylinder.
  5. Turn on gas supply to the heater and check all fittings and connections for gas leaks using mild soap and water solution. NEVER INSPECT FOR LEAKS USING A MATCH OR ANY OTHER TYPE OF FLAME. Should a gas leak occur, shut off the gas supply to the heater immediately and wait a minimum of five minutes before repairing the leak.
  6. When assured that there are no leaks, light heater/pilot. If heater/pilot does not ignite within 5 seconds, extinguish flame and shut off gas valve. Wait 5 minutes before retrying.
  7. (#006139 heaters) Once pilot is lit, let run for 3-5 minutes, try on/off cycle 2 to 3 times.
  8. (#006187 heaters) Once pilot is lit, turn heater on, let run for 3-5 minutes; try on/off cycle 2 to 3 times.
  9. If heater fails, determine if economical to repair, send to a certified repair shop.
  10. Inspect auto shut off valve is in working condition by tipping unit over (if applicable.)

D. Repackaging

  • Use Carton NFES 8199 16 x16 x 36 1 EA 
  • Palletize so Heater is situated upright (if feasible)

E. Attachments

Image
NFES 6187 showing Tip-Over Safety Switch on underside of heater unit.

 

NWCG Latest Announcements

Updated NWCG Standards for Fire Unmanned Aircraft Systems Operations, PMS 515

Date: April 23, 2025
Questions?  Please contact:
Interagency Fire Unmanned Aircraft Systems Subcommittee

The NWCG Standards for Fire Unmanned Aircraft Systems Operations, PMS 515 standardizes processes and procedures for the interagency use of Unmanned Aircraft Systems (UAS), including pilot inspections and approvals. This updated publication provides the aviation community with standards to ensure UAS are used safely, effectively, and efficiently in support of fire management goals and objectives.

References:

NWCG Standards for Fire Unmanned Aircraft Systems Operations, PMS 515

NWCG National Interagency Aviation Committee

ETC Bulletin 25-001: Retrofitted Hot/Cold Beverage Kits - 2025 Field Season

Date: April 16, 2025
Questions?  Please contact:
Equipment Technology Committee

Due to spout failures and the associated risk of burn injuries, manufacturers have retrofitted the Hot/Cold Beverage Kits using a heat-shrinking band to secure the black spout at the insertion site. The updated kits feature a fluorescent label on each full kit assembly for easy identification. Catering units are encouraged to confirm the clear heat-shrinking bands are intact around each spout before filling.

ETC Bulletin 24-001 regarding Hot/Cold Beverage Kits has been archived and replaced by ETC Bulletin 25-001 for the 2025 season.

References:

NWCG Alerts

ETC-EB-25-001 Retrofitted Hot/Cold Beverage Kits

NWCG Standards for Wildland Fire Chainsaw Operations, PMS 212, and Next Generation Position Task Book for Basic Faller Are Now Available

Date: April 14, 2025
Questions?  Please contact:
Hazard Tree and Tree Felling Subcommittee

The updated NWCG Standards for Wildland Fire Chainsaw Operations, PMS 212, and NWCG Position Task Book for Basic Faller (FAL3), PMS 311-19 are now available.

The NWCG Standards for Wildland Fire Chainsaw Operations, PMS 212 includes position standards designed to be used in conjunction with the Next Generation Position Task Book (Next Gen PTB). The Next Gen PTB for Basic Faller (FAL3) includes an evaluation guide with suggested rating elements to consider when assessing trainees.

References:

NWCG Standards For Wildland Fire Chainsaw Operations, PMS 212

NWCG Position Task Book for Basic Faller (FAL3), PMS 311-119

NWCG Basic Faller (FAL3)

RMC Memo 25-01: Summary of Updates to Safety Officer Positions

Date: April 9, 2025
Questions?  Please contact:
RMC Member Eric Fransted

The Risk Management Committee (RMC) serves as the position steward for all Safety Officer incident positions and continues to improve position standards, training, and naming conventions. The implementation of Complex Incident Management (CIM) required changes to position titles. RMC collaborated with the NWCG Incident Position Standards Committee (IPSC) to propose and implement these updates. 

References:

RMC Memo 25-01: Summary of Updates to Safety Officer Positions 

NWCG Position Catalog