Skip to main content

Air Operations Map

Product Description

The Air Operations Map provides air operations with enough detail to aid in locating key features on an incident.  A secondary Air Operations map, the Pilot Map, may be created for pilots.

Target Audience

Air Operations Branch, pilots 

Guidelines

  • Standard Incident Command System (ICS) symbology.
  • Minimal clutter on map.
  • A table that includes the latitude and longitude coordinates in Degrees, Decimal Minutes for point features.
  • Pilot map is typically small for easy lap reading in the aircraft.

Standard Elements

All map products produced should include the STANDL-SGD cartographic elements.  Scale bar must be in nautical miles rather than statute miles.

Data

  • Incident perimeter, ICS line and limited/relevant point features.
  • Division and Branch breaks and labels.
  • Airports, helibases.
  • Aviation hazards (e.g., transmission lines, mountain peaks with elevation labels, towers).
  • Table or labels showing latitude and longitude of key locations.
  • Roads.
  • Key landmarks.
  • Hydrography (e.g., rivers, lakes).
  • Temporary Flight Restrictions (TFRs) (when in place) and TFR number, height, and frequency, if available.
  • Elevation shaded relief or Federal Aviation Administration sectionals.
  • Other SITL-requested data.

Examples

These are examples from actual incidents and may include non-standard elements.

Also note that examples use the standard symbols at the time of their creation and may not reflect the current GeoOps symbology. Map elements, incident features, and composition remain consistent across these visual changes.

  1. Air Operations Map - Cedar Creek and Cub Creek 2
  2. Air Operation Map - Delta Lake
  3. Air Operations Map - 2010 Wrangler Fire
  4. Pilot Map - 2023 Flying V
  5. Pilot Map - 2016 Beaver Creek Fire
  6. Pilot Map - 2017 Pinal Fire
  7. Air Operations Map - 2015 National Creek Complex

 

Last Modified / Reviewed:

Print PDF

NWCG Latest Announcements

Updated NWCG Standards for Airtanker Base Operations, PMS 508

Date: March 31, 2025
Questions?  Please contact:
Airtanker Base Operations Unit

The updated NWCG Standards for Airtanker Base Operations (SABO), PMS 508 standardizes operations and procedures at interagency airtanker bases to ensure safe, efficient, and effective operations in support of interagency goals and objectives.

References:

NWCG Standards for Airtanker Base Operations, PMS 508

WFSTAR 2025 Core Component Module Package and 2024 Fire Year in Review Now Available

Date: March 14, 2025
Questions?  Please contact:
Joe Schindel at mschindel@blm.gov
 

The 2025 Core Component Module Package for RT-130, Wildland Fire Safety Training Annual Refresher (WFSTAR) and the 2024 Fire Year in Review are now available on the NWCG website. The 2025 Core Component Module Package provides all content needed to deliver RT-130.

References:

2025 Core Component Module Package

2024 Fire Year in Review Module

NEW! NWCG Wildland Urban Interface Mitigation Field Guide, PMS 053

Date: March 12, 2025
Contact: Wildland Urban Interface Mitigation Committee

The NWCG Wildland Urban Interface Mitigation Field Guide, PMS 053 provides mitigation practitioners at all experience levels with recommendations on the most effective and efficient ways to accomplish mitigation work in communities at risk to wildfire damage or destruction. The content in this guide was written in coordination with the NWCG Standards for Mitigation in the Wildland Urban Interface, PMS 052.

References:

NWCG Wildland Urban Interface Mitigation Field Guide, PMS 053 

Updated, NWCG Standards for Wildland Fire Module Operations, PMS 430

Date: March 11, 2025
Contact: Fire Use Subcommittee
Wildland Fire Module Unit

The NWCG Standards for Wildland Fire Module Operations, PMS 430 standardizes procedures and expectations for Wildland Fire Modules (WFMs). These standards are to be used by staff, supervisors, specialists, and technicians for planning, administering, and conducting WFM operations. These standards will also be used as a measure of WFM qualifications, capabilities, and expected performance, for both Type 1 and Type 2 WFMs.

References:

NWCG Standards for Wildland Fire Module Operations, PMS 430