Skip to main content

1.5 Division

DIVISION: DIVIDING INTO SMALLER PARTS

Division is used to split groups up into smaller sections. Suppose there are 24 pairs of gloves in the storage locker and you want to distribute them evenly among 8 crewpeople. How many pairs of gloves would each crewperson receive. Dividing 24 by 8 yields 3; each crewperson would receive 3 pairs of gloves. Some words and symbols often seen in division are divided byinto, the symbol "÷",and the symbol "/". Just as multiplication is thought of as repeated addition, division can be thought of as repeated subtraction.

Some terms used in division include:
Divisor - the number by which a larger number is divided.
Dividend - the sum or amount to be divided and distributed.
Quotient - the number resulting from the division of one number by another .
Remainder - the number left after division that is smaller than the divisor.

In the equation b/a = c, b is the dividend, a is divisor, and c is the quotient.


Example 1- There are 20 nozzles for 5 engines. If the nozzles were to be divided evenly for the engines, how many nozzles would go on each engine?

20 - 5 = 15 - 5 = 10 - 5 = 5 - 5 =0. In this case, 5 was subtracted from 20 a total of 4 times. The answer to 20 divided by 5 is written as 20 ÷ 5 = 4
 

Example 2 - Divide 15 by 4.
15 - 4 = 11 - 4 = 7 - 4 = 3
Because 4 cannot be subtracted from 3, the 3 is called the remainder and is noted by the symbol "R".

The remainder is never larger than the divisor. The divisor in this example is 4. So, 15 / 4 = 3 R 3

If these were fifteen nozzles for four engines on your district, four nozzles would go on three engines and only three nozzles would go on the last engine. 
 

LONG DIVISION FOR LARGER NUMBERS

Long division can be used when working with larger numbers. Here the repeated subtraction is done in a different way. To divide, start from the digit of highest place value and finish with the digit in the lowest place value. At each step, ask if there are multiples of the number in the answer. 

Example 3 - Divide 3654 by 5.

Division Example
Step 1. Start with the thousands digit in the number being divided. 5 is larger than 3, so move to the next step.

Step 2. Look at the hundreds place. Can 5 go into 36? Yes: 7 × 5 = 35. Fill in the ones and tens places with "0"s and subtract.

Step 4. Go to the tens place of the remainder (the number 154) that was subtracted in the previous step. Can 5 go into 15? Yes: 5 × 3 = 15. Fill in the "0" in the ones place and subtract

Step 5. Go to the ones place. Can 5 go into 4? No. 4 is smaller than 5. Put a "0" in the ones spot of the answer. There is a remainder of 4.

The answer to 3,654 ÷ 5 is written 730 R 4
To check the answer to this long division problem, multiply 730 × 5 to give 3,650. Adding the remainder of 4 gives 3654. The original dividend was 3654, so the answer is correct.
 

DIVIDING SIGNED NUMBERS

Dividing signed numbers follows the same general rules as multiplication. When dividing any two numbers having the same sign, the answer is positive, while that of two numbers of opposite sign is negative. When dividing numbers with like signs, the answer is positive. When dividing numbers with unlike signs, the answer is negative.
20 ÷ (-4) = -5
48 ÷ (-8) = -6
-100 ÷ (-10) = 10
-49 ÷ 11 = -4 R 5

 

NWCG Latest Announcements

Updated NWCG Standards for Fire Unmanned Aircraft Systems Operations, PMS 515

Date: April 23, 2025
Questions?  Please contact:
Interagency Fire Unmanned Aircraft Systems Subcommittee

The NWCG Standards for Fire Unmanned Aircraft Systems Operations, PMS 515 standardizes processes and procedures for the interagency use of Unmanned Aircraft Systems (UAS), including pilot inspections and approvals. This updated publication provides the aviation community with standards to ensure UAS are used safely, effectively, and efficiently in support of fire management goals and objectives.

References:

NWCG Standards for Fire Unmanned Aircraft Systems Operations, PMS 515

NWCG National Interagency Aviation Committee

ETC Bulletin 25-001: Retrofitted Hot/Cold Beverage Kits - 2025 Field Season

Date: April 16, 2025
Questions?  Please contact:
Equipment Technology Committee

Due to spout failures and the associated risk of burn injuries, manufacturers have retrofitted the Hot/Cold Beverage Kits using a heat-shrinking band to secure the black spout at the insertion site. The updated kits feature a fluorescent label on each full kit assembly for easy identification. Catering units are encouraged to confirm the clear heat-shrinking bands are intact around each spout before filling.

ETC Bulletin 24-001 regarding Hot/Cold Beverage Kits has been archived and replaced by ETC Bulletin 25-001 for the 2025 season.

References:

NWCG Alerts

ETC-EB-25-001 Retrofitted Hot/Cold Beverage Kits

NWCG Standards for Wildland Fire Chainsaw Operations, PMS 212, and Next Generation Position Task Book for Basic Faller Are Now Available

Date: April 14, 2025
Questions?  Please contact:
Hazard Tree and Tree Felling Subcommittee

The updated NWCG Standards for Wildland Fire Chainsaw Operations, PMS 212, and NWCG Position Task Book for Basic Faller (FAL3), PMS 311-19 are now available.

The NWCG Standards for Wildland Fire Chainsaw Operations, PMS 212 includes position standards designed to be used in conjunction with the Next Generation Position Task Book (Next Gen PTB). The Next Gen PTB for Basic Faller (FAL3) includes an evaluation guide with suggested rating elements to consider when assessing trainees.

References:

NWCG Standards For Wildland Fire Chainsaw Operations, PMS 212

NWCG Position Task Book for Basic Faller (FAL3), PMS 311-119

NWCG Basic Faller (FAL3)

RMC Memo 25-01: Summary of Updates to Safety Officer Positions

Date: April 9, 2025
Questions?  Please contact:
RMC Member Eric Fransted

The Risk Management Committee (RMC) serves as the position steward for all Safety Officer incident positions and continues to improve position standards, training, and naming conventions. The implementation of Complex Incident Management (CIM) required changes to position titles. RMC collaborated with the NWCG Incident Position Standards Committee (IPSC) to propose and implement these updates. 

References:

RMC Memo 25-01: Summary of Updates to Safety Officer Positions 

NWCG Position Catalog