Skip to main content

5.5 Contour Lines and Intervals

A contour line is a line drawn on a topographic map to indicate ground elevation or depression. A contour interval is the vertical distance or difference in elevation between contour lines. Index contours are bold or thicker lines that appear at every fifth contour line.

image of topographic map

If the numbers associated with specific contour lines are increasing, the elevation of the terrain is also increasing. If the numbers associated with the contour lines are decreasing, there is a decrease in elevation. As a contour approaches a stream, canyon, or drainage area, the contour lines turn upstream. They then cross the stream and turn back along the opposite bank of the stream forming a "v". A rounded contour indicates a flatter or wider drainage or spur. Contour lines tend to enclose the smallest areas on ridge tops, which are often narrow or very limited in spatial extent. Sharp contour points indicate pointed ridges. 

Example 1 - In the graphic below, what is the vertical distance between the contour lines?

contour lines

Pick two contour lines that are next to each other and find the difference in associated numbers.
40 feet - 20 feet = 20 feet

The contour lines in this figure are equally spaced. The even spacing indicates the hill has a uniform slope. From the contour map, a profile can be drawn of the terrain.

Example 2 - Draw a profile showing the elevations of the contours.

Note: The intervals are increasing, therefore, the contours indicate a hill. The peak is normally considered to be located at half the interval distance.

contours

Widely separated contour lines indicate a gentle slope. Contour lines that are very close together indicate a steep slope.

contours

contours

The figure above illustrates various topographic features. (b) Notice how a mountain saddle, a ridge, a stream, a steep area, and a flat area are shown with contour lines.

topo feature

The figure above illustrates a depression and its representation using contour lines. Notice the tick marks pointing toward lower elevation.

5_34[1].gif
Figure One
5_33[1].gif
Figure Two
 

SLOPE PERCENT FROM TOPOGRAPHIC MAP

The horizontal distance between points A and B can be measured with a scaled ruler and used to determine the slope percent.

slope percent = rise/run × 100

Example 4 - What is the slope percent in Exercise 2 above? 

slope percent = rise/run × 100.

For this computation, the rise, or vertical ground distance, and run, or horizontal ground distance, are needed.

Step 1. Measure the horizontal map distance between points A and B to get the vertical ground distance.
The horizontal map distance measures 0.5 inches.

Step 2. Use the appropriate conversion factor to convert the horizontal map distance to horizontal ground distance.
0.5 in × 24,000 in/in = 12,000 in

Step 3. The desired unit is feet. Set up the cancellation table so all units will cancel, except the desired unit, feet.

cancellation table
Step 4. Use the slope percent equation and solve. The run is 1000 feet and the rise in elevation is 120 feet. 

slope percent = rise/run × 100

slope percent = (120ft / 1000ft) × 100 = 12%

Slope Worksheet - Use the information from the example above and complete the slope worksheet. Line 1 starts with the contour interval, not the projection point. 

Slope Worksheet (to be completed)

Line Input    
0 PP Projection point ______
1 CON INT Contour interval, ft ______
2 SLC Map Scale ______
3 CF Conversion factor, ft/in ______
4 #INTVLS # of contour intervals ______
5 RISE Rise in elevation, ft ______
6 MD Map distance, in (between points) ______
7 HZGD Horizontal ground distance, ft ______
  Output    
  SLP% SLOPE% ______

Slope Worksheet (completed)

Line Input    
0 PP Projection point A-B
1 CON INT Contour interval, ft 40
2 SLC Map Scale 1:24,000
3 CF Conversion factor, ft/in 2,000
4 #INTVLS # of contour intervals 3
5 RISE Rise in elevation, ft 120
6 MD Map distance, in (between points) 0.5
7 HZGD Horizontal ground distance, ft 1,000
  Output    
  SLP% SLOPE% 12

NWCG Latest Announcements

Updated NWCG Standards for Fire Unmanned Aircraft Systems Operations, PMS 515

Date: April 23, 2025
Questions?  Please contact:
Interagency Fire Unmanned Aircraft Systems Subcommittee

The NWCG Standards for Fire Unmanned Aircraft Systems Operations, PMS 515 standardizes processes and procedures for the interagency use of Unmanned Aircraft Systems (UAS), including pilot inspections and approvals. This updated publication provides the aviation community with standards to ensure UAS are used safely, effectively, and efficiently in support of fire management goals and objectives.

References:

NWCG Standards for Fire Unmanned Aircraft Systems Operations, PMS 515

NWCG National Interagency Aviation Committee

ETC Bulletin 25-001: Retrofitted Hot/Cold Beverage Kits - 2025 Field Season

Date: April 16, 2025
Questions?  Please contact:
Equipment Technology Committee

Due to spout failures and the associated risk of burn injuries, manufacturers have retrofitted the Hot/Cold Beverage Kits using a heat-shrinking band to secure the black spout at the insertion site. The updated kits feature a fluorescent label on each full kit assembly for easy identification. Catering units are encouraged to confirm the clear heat-shrinking bands are intact around each spout before filling.

ETC Bulletin 24-001 regarding Hot/Cold Beverage Kits has been archived and replaced by ETC Bulletin 25-001 for the 2025 season.

References:

NWCG Alerts

ETC-EB-25-001 Retrofitted Hot/Cold Beverage Kits

NWCG Standards for Wildland Fire Chainsaw Operations, PMS 212, and Next Generation Position Task Book for Basic Faller Are Now Available

Date: April 14, 2025
Questions?  Please contact:
Hazard Tree and Tree Felling Subcommittee

The updated NWCG Standards for Wildland Fire Chainsaw Operations, PMS 212, and NWCG Position Task Book for Basic Faller (FAL3), PMS 311-19 are now available.

The NWCG Standards for Wildland Fire Chainsaw Operations, PMS 212 includes position standards designed to be used in conjunction with the Next Generation Position Task Book (Next Gen PTB). The Next Gen PTB for Basic Faller (FAL3) includes an evaluation guide with suggested rating elements to consider when assessing trainees.

References:

NWCG Standards For Wildland Fire Chainsaw Operations, PMS 212

NWCG Position Task Book for Basic Faller (FAL3), PMS 311-119

NWCG Basic Faller (FAL3)

RMC Memo 25-01: Summary of Updates to Safety Officer Positions

Date: April 9, 2025
Questions?  Please contact:
RMC Member Eric Fransted

The Risk Management Committee (RMC) serves as the position steward for all Safety Officer incident positions and continues to improve position standards, training, and naming conventions. The implementation of Complex Incident Management (CIM) required changes to position titles. RMC collaborated with the NWCG Incident Position Standards Committee (IPSC) to propose and implement these updates. 

References:

RMC Memo 25-01: Summary of Updates to Safety Officer Positions 

NWCG Position Catalog