Skip to main content

6.11 Base, Township, Range, Sections, & Corners

Base and meridian lines are similar to latitude and longitude lines. Use geographic locations, such as prominent features of the area, as reference points.

Townships are rectangular blocks of land about 6 miles square. The squares are gridded and numbered according to their position north or south of the base line.

Ranges are columns of townships set side by side. They are numbered starting at the meridian that runs through the point of origin of each system. Ranges run east and west.

Sections represent further divisions of a township. A township can be divided into 36 sections. Each section is about 1 square mile. Sections are numbered from the top right, or northeast section, then to the left, and down in an "S" formation. The section below is taken from T.2S., R.2E. Any township can be found by identifying the township number, then the range number, and finally the base and meridian system.

Corners describe areas within a section to provide more specific location information. Corners can be described as northeast, southeast, northwest, and southwest. There are corners within corners. For example, the figure below indicates a lightning strike at the point labeled "X" in section 22. The lightning strike is located in the northwest corner of the northwest corner of section 22 of T.2S., R.2E. 

The legal description of land begins with the smallest unit and ends with the largest unit. In the case below, the section location is written as T.2S., R.2E., M.D.M., which describes Township 2 South, Range 2
East, Mt. Diablo Meridian. 
base / meridian chart



Example 1 - What is the township, range, and section of the lightning strike labeled "X" in the figure?

Step 1. Write the township.
T.2S.

Step 2. Write the range.
R.2E.

Step 3. Write the section.
22

Example 2 - What would you tell the dispatcher is the exact location of the lightning strike using corners?

Step 1. Write the corners.
Northwest corner of the northwest corner

Step 2. Write the section.
22

Step 3. Write the township and range.
T.2S., R.2E.

NW corner of the NW corner, Section 22, T.2S., R.2E.

NWCG Latest Announcements

NEW! S-130, Firefighter Training (Blended) Now Available

Date: June 10, 2025
If you have questions, please visit our FAQ page. 
If your question is not answered there, you can 
submit your question using our Contact Us form. 
 

The S-130, Firefighter Training (Blended), equips new wildland firefighters with essential skills through a mix of online learning and hands-on training. The course features a required online component and an instructor-led exercise, reinforcing online concepts with practical performance-based training.

The course builds competencies in wildland fire operations, safety, and equipment use, applicable across various operational environments. Both the online component and instructor-led field exercise must be completed to receive a certificate of completion. Students are required to finish the prerequisite S-190, Introduction to Wildland Fire Behavior, before enrolling in S-130, Firefighter Training (Blended).

References:

S-130, Firefighter Training (Blended)

S-190, Introduction to Wildland Fire Behavior

Wildland Fire Learning Portal

EMC Memo 25-001: Interim Rapid Extraction Module (REMS) Training and Qualification Requirements

Date: June 3, 2025
Questions?  Please contact:
Emergency Medical Committee

The Emergency Medical Committee has issued interim guidance for Rapid Extraction Module Support (REMS) teams. Until further notice, Type I and II REMS teams must designate a team leader qualified at Firefighter Type 1 Squad Boss (FFT1) or higher. This temporary change replaces the Single Resource Boss (SRB) requirement, which is currently not feasible due to administrative barriers.

This memorandum does not include any other changes to the NWCG Standards for Rapid Extraction Module Support, PMS 552. This interim change takes effect immediately and will remain in place until further notice.

References:

EMC Memo 25-001: Interim Rapid Extraction Module (REMS) Training and Qualification Requirements

NWCG Standards for Rapid Extraction Module Support, PMS 552

Equipment Bulletin 25-002: Chaps, Chain Saw, M-2020, Nonconformities Affecting Use, Appearance, and Serviceability

Date: June 2, 2025
Questions?  Please contact:
Equipment Technology Committee

The Equipment Technology Committee issued Equipment Bulletin: 25-002 to address a manufacturing nonconformity affecting Forest Service specification, 6170-4K Chain Saw Chaps. The issue applies to chaps manufactured in 2024 and 2025 and distributed through FedMall. These chaps may have incorrectly bound edges that expose inner protective layers.

Independent purchasers should inspect all chain saw chaps received from FedMall beginning in 2024, prior to use. Review the full Equipment Bulletin: 25-002 for inspection criteria and recommended actions.

References:

NWCG Alerts

ETC Equipment Bulletin: 25-002

2024 Wildland Fire Emergency Medical Service Awards

Date: May 22, 2025
Questions?  Please contact:
Emergency Medical Committee

The NWCG Emergency Medical Committee (EMC) is proud to announce the recipients of the 2024 Wildland Fire Emergency Medical Service Awards. Each year, EMC recognizes individuals and groups who have demonstrated exceptional actions or accomplishments that go above and beyond their normal mission or job duties.

Congratulations to all the awardees and nominees. Through leadership and initiative, they have made significant contributions to the safety and well-being of the wildland fire community. These honors are well deserved.

References:

2024 Wildland Fire EMS Awards

NWCG Emergency Medical Committee