Skip to main content

Firefighter Math: 8.2 Midflame Windspeed

Midflame windspeed (MFWS) is defined as the velocity of the winds, in miles per hour (mi/hr), taken at the mid-height of the flames. MFWS will directly affect the direction of movement of the flaming front and is important in fire spread calculations. The midflame windspeed is determined by use of the wind adjustment table, which provides values in terms of fuel overstory exposure and fuel model. 
table showing adjustment factors for different fuel shelterings

Figure 8.2 Adjustment factors for midflame winds.
The adjustment values are typically applied to the 20-foot windspeed, which is the speed that is measured 20 feet above any fuel or obstruction, usually by a weather station. The midflame windspeed is obtained by multiplying the 20-foot windspeed by the appropriate wind adjustment factor from the table. 

graphic showing different fuel shelterings

Figure 8.3 Effects of fuel sheltering on wind speeds.
It is very important to know which fuel model and sheltering configuration is being studied, and whether a given windspeed is a 20-ft windspeed or an already adjusted midflame windspeed. 

graphic showing friction effects slowing wind

Figure 8.4 Typical fuel sheltering for slope locations.
The midflame windspeed will be LESS THAN the 20-foot windspeed, because vegetation and friction slow down winds closer to the surface. That is why all the adjustment factors in the table are less than 1. 

Example 1 - A fire is burning in a fully sheltered area of dense, or closed, stands described as Fuel Model 4. The local weather station reports the 20-ft windspeed is 15 miles per hour. What is the midflame windspeed? Show all work on the wind adjustment worksheet (see below).

Solution - The figure above describes wind reduction factors and is used to determine the appropriate correction factor.

Step 1. The correction factor is 0.1 for any fuel model under fully sheltered conditions with dense stands.

Step 2. To find the midflame windspeed, multiply the 20-foot windspeed by the adjustment factor.
midflame windspeed =
20-foot windspeed × adjustment factor

MFWS = 15 mi/h × 0.1 = 1.5 mi/h

Example 2 - A 20-foot windspeed at the top of the ridge is reported to be 35 miles per hour, with fuel model 11 vegetation. What is the midflame windspeed? 

Step 1. See figure 8.4. The top of a ridge is indicated to be unsheltered.

Step 2. From figure 8.2, the adjustment factor is 0.4.

Step 3. MFWS = 35 x 0.4 = 14 mi/h

The values can be summarized in a wind adjustment worksheet. 
graphic of completed wind adjustment worksheet

 

NWCG Latest Announcements

2025/2026 Leadership Campaign Quarter 2 Now Available!

Date: February 13, 2026
Questions? 
Please contact: Leadership Committee

NWCG is excited to announce that the Quarter Two materials for the 2025/2026 Wildland Fire Leadership Campaign are now available! This annual initiative invites all leadership and wildland fire management students to engage with essential skills and knowledge needed to lead effectively in dynamic environments.

This quarter focuses on Leadership Level 2: New Leader (Conveying Intent). Conveying intent is a crucial leadership competency in the high-risk, dynamic environment of wildland firefighting. Months 4 - 6 will concentrate on how successfully conveying intent enhances situational awareness, promotes shared understanding, and empowers firefighters to exercise initiative and adapt to changing conditions.

References:

2025/2026 NWCG Leadership Campaign - Leadership Levels

Wildland Fire Leadership Development Program

Leadership Committee

Opportunity to Serve the Wildland Fire Community as an IPTM SME!

Date: February 10, 2026
Questions? 
Please contact: NWCG SME Specialist

NWCG is seeking experienced wildland firefighters and support personnel to serve as Subject Matter Experts (SMEs) for the Incident Performance and Training Modernization (IPTM) initiative. The intent of IPTM is to transition NWCG’s training and qualification system to a performance-based model through updated position descriptions, Incident Position Standards, Next Generation Position Task Books (Next Gen PTBs), and updates to training where needed.

NWCG is currently recruiting SMEs for the following positions:

  • Aircraft Timekeeper (ATIM)
  • Compensation/Claims Unit Leader (COMP)
  • Cost Unit Leader (COST)
  • Crew Representative (CREP)
  • Deck Coordinator (DECK)
  • Fire Effects Monitor (FEMO)
  • Field Observer (FOBS)
  • Geographic Information System Specialist (GISS)
  • Ordering Manager (ORDM)
  • Receiving/Distribution Manager (RCDM)
  • Staging Area Manager (STAM)

Projects begin April/May 2026 and require 15–20 hours per month for 6–8 months, including a five-day workshop in Boise, Idaho this May. Apply by February 27, 2026, at the link below and review the attached document for details.

References:

NWCG SME Interest Sign-up

IPTM Subject Matter Expert Duties and Expectations Document

Incident Performance and Training Modernization (IPTM)

NEW! M-280, Resource Advisor, Fireline (Instructor-Led) Course Available Now

Date: January 29, 2026
Questions? 
Please contact: Resource Advisor Subcommittee

NWCG is pleased to announce the new M-280, Resource Advisor, Fireline (Instructor-Led) course is now available. This training supports individuals working towards Resource Advisor, Fireline (REAF) incident qualifications.

M-280, Resource Advisor, Fireline (Instructor-Led) training prepares students to serve as a Resource Advisor, Fireline (REAF) as defined in NWCG Incident Position Standards for Resource Advisor, Fireline, PMS 350-112. This course presents scenarios that reflect the diverse challenges a REAF may encounter during an incident. Through these scenarios, participants gain hands-on experience and an understanding of REAF responsibilities in a controlled learning environment.

References:

Resource Advisor, Fireline Position Page

NWCG Position Standards for Resource Advisor, Fireline, PMS 350-112

M-280, Resource Advisor, Fireline (Instructor-Led)

Wildland Fire Learning Portal

2026 Updates to the NWCG Standards for Wildland Fire Position Qualifications, PMS 310-1

Date: January 23, 2026
Questions? 
Please contact: Incident and Position Standards Committee

The Incident and Position Standards Committee has updated the NWCG Standards for Wildland Fire Position Qualifications, PMS 310-1.

These updates address changes to incident position names and requirements for qualification, training, and experience. Updates related to the implementation of Complex Incident Management (CIM) and Incident Performance Training Modernization (IPTM) are also included.

The NWCG Wildland Fire Position Qualification Flowchart, PMS 308 has also been updated to reflect the recent changes.

References:

NWCG Standards for Wildland Fire Position Qualifications, PMS 310-1

NWCG Wildland Fire Position Qualification Flowchart, PMS 308

IPSC Memo 26-01: January 2026 Updates to the NWCG Standards for Wildland Fire Positions Qualifications, PMS 310-1