Skip to main content

3.4 Calculating Engine Pump Pressures

To achieve a desired nozzle pressure (DNP), a few factors must be considered. First, you must note the head loss (HL) or head gain (HG). Water head is the height of the water column (lift) due to imposing pressure. The head pressure is positive (gain) if the hose lay is downhill because the force of gravity is helping push the water down, consequently increasing the pressure. The head pressure is negative (loss) if the hose lay is uphill, since the force of gravity is pulling the water down, when it needs to be pumped up. Table 3.1 indicates that 1 foot of water head or lift produces 0.5 pounds per square inch of pressure. On that same note, 1 pound per square inch can produce 2 feet of water head). For every foot uphill or downhill, there is a change of 0.5 pounds per square inch of pressure. Note that this measurement represents the height of the hose (elevation) and not the length of the hose.

Water Pressure vs Height
 

Water Pressure vs Height. The drawings correspond to the pressure on a square inch cross section caused by the height of water above it. Note that as the column's height doubles, so does the pressure. Both exact and rounded field application values are given.

FRICTION LOSSES

The second consideration for pump pressure calculations involves friction loss (FL). As a field rule, the pressure in a line is reduced by 5 pounds per square inch for each appliance added to the line. For example, a hose lay with five wye valves will result in a 25 pounds per square inch pressure loss due to the friction introduced by these fittings. This approximation is used to simplify calculations and is not precisely what occurs in the field. See Table 3.3 for friction loss in forestry hose.
 

CALCULATING DESIRED NOZZLE AND PUMP PRESSURES

Engine and nozzle pressures are calculated as follows:
DNP = Desired Nozzle Pressure
EP = Engine Pressure
HG = Head Gain
HL = Head Loss
FL = Friction Loss

Desired Nozzle Pressure equals:
Engine (Pump) Pressure ± (Head Gain or Head Loss) - Friction Loss
    DNP = EP ± (HG or HL) - FL

When calculating desired nozzle pressure in a downhill hose lay, add the head pressure. In uphill hose lays, subtract the head pressure. The calculations vary to account for the work of gravity.
 

The head pressure is expressed in terms of loss or gain. Because the pump and the nozzle are at opposite ends of the hose, head pressure that is positive at the pump will be negative at the nozzle and vice versa. It is crucial that the sign of the head pressure be correct. If the hose lay is uphill, the head pressure is negative, and if it is downhill, the head pressure is positive. Careful attention must be paid to the sign of the head gain or head loss term, and whether the gain or loss should be added or subtracted.

Head Gain and Loss
Head gain and head loss depend on the nozzle's position relative to the pump.
 

ESTIMATING IN THE FIELD

As mentioned earlier, it is often necessary to round numbers either up or down to make calculations easier. When precise calculation is not possible because there is no paper, pen, or calculator, rounded estimations are helpful. In the field, rounding does not greatly affect the results. It can helpful to round numbers to take outside disturbances of any kind into account. For example, rounding the pressure caused by water head up from 0.434 to 0.5 takes into account any additional friction that might be caused by the hose itself.

For a 100-foot vertical height of water in the hose, using the exact value of 0.434 pounds per square inch per foot would give a 43 pounds per square inch (psi) head loss. This loss is 7 pounds per square inch less than what was calculated earlier. By rounding up to 0.5 from 0.434, friction and head losses due to the hose itself are taken into account, and no additional calculation is needed. In the field, the 0.5 pounds per square inch head loss is therefore used. This approximation not only eases calculations, but is more realistic to use in the field.
 

FRICTION DUE TO HOSE LENGTH

For hose lengths longer than 100 feet, friction loss in the hose should be considered. Friction loss of a 100-foot, 1-inch hose, all synthetic, with volume rate of 15 gallons per minute, is typically 4 to 9 pounds per square inch. Friction loss of a 100-foot, 1-inch hose, cotton-synthetic, at 15 gallons per minute, is typically 3 to 6 pounds per square inch. Friction loss for a 1.5-inch hose at 15 gallons per minute is typically 1 pound per square inch for 100 feet. See Table 3.3. 

Example 1 - A progressive hose lay has six gated wye valves along the length of the trunk line. The nozzle outlet is 200 feet below the engine. The desired nozzle pressure of the trunk line is 100 pounds per square inch. At what pressure does the engine need to perform?

Step 1. Find the appropriate conversion/estimation in Table 3.1 for the pressure caused by 1 foot of water head. 1 ft = 0.5 psi

Step 2. Set up the cancellation table so all units will cancel, except the desired unit, psi. There is a head gain due to the hose lay being downhill.

cancellation table

Step 3. Set up the cancellation table so all units will cancel, except the desired unit, psi, to calculate the friction loss due to the fittings. Guidelines indicate a 5 pounds per square inch loss per fitting.

cancellation table

Step 4. Use the equation for the engine pressure. EP = DNP ± HG (or HL) +FL

Step 5. Identify the DNP, the HG, and the FL. DNP = 100 psi, HG = 100 psi, FL = 30 psi

Step 6. Set up the problem and solve. EP = 100 psi - 100 psi + 30 psi

The engine pressure needs to be 30 pounds per square inch for a desired nozzle pressure of 100 pounds per square inch in this hose lay.
 

STEP-BY-STEP PRACTICE

Kevin is fighting a fire and needs the nozzle pressure to be 100 pounds per square inch. He is 100 feet above the engine. What pump pressure does he need? Proceed through the questions below, which correspond to the steps necessary to solve the problem. After each step, click the next question button until you have reached the end of the exercise and have a value, in psi, for the engine pump pressure needed.
 

Pressure vs Height

 

SIZE AND SHAPE VERSUS PRESSURE

The width or diameter of the tank does not affect the pressure. A column of water 100 feet high creates the same amount of pressure in a 2-foot diameter tank as it does in a 20-foot diameter tank. Think of people swimming in the ocean. They are not crushed by the pressure of such a large body of water because the pressure is the same if the height is the same, no matter how wide or what shape the container. 

Different shaped tanks

Different shaped tanks exhibit the same pressure.

WATER LEVELS

Knowing that 1 pound per square inch of pressure can lift water vertically 2 feet, the water level of certain volumes of water (a cistern or tank) can also be calculated.

Example 2 - An engine's compound gauge is connected at the base of a 100-foot tall reservoir tank, and the gauge reads 35 pounds per square inch. How high is the water level in the reservoir?

Example 2 image

Step 1. Find the appropriate conversion/estimation in table 3.1 for the height of water that creates 1 pound per square inch of pressure. 1 psi = 2 ft of water head

Step 2. Set up the cancellation table so all units will cancel, except the desired unit, feet, to calculate the height of water that creates the 35 pounds per square inch of pressure above the gauge.

Cancellation Table

The water level is 70 feet above the gauge.

MORE PRACTICE

Harvey has parked his engine 30 feet below the base of a nearby water tank. He connects his engine's compound gauge to the water line coming from the tank and obtains a reading of 40 pounds per square inch. How high is the water level in the tank? 

In this problem, the pressure is read not at the base of the tank, but at 30 feet below.

Pressure vs Height

Hint. Find the appropriate conversion/estimation in Table 3.1 for the height of water that creates 1 pound per square inch of pressure. 1 psi = 2 feet

 

NWCG Latest Announcements

Updated NWCG Standards for Fire Unmanned Aircraft Systems Operations, PMS 515

Date: April 23, 2025
Questions?  Please contact:
Interagency Fire Unmanned Aircraft Systems Subcommittee

The NWCG Standards for Fire Unmanned Aircraft Systems Operations, PMS 515 standardizes processes and procedures for the interagency use of Unmanned Aircraft Systems (UAS), including pilot inspections and approvals. This updated publication provides the aviation community with standards to ensure UAS are used safely, effectively, and efficiently in support of fire management goals and objectives.

References:

NWCG Standards for Fire Unmanned Aircraft Systems Operations, PMS 515

NWCG National Interagency Aviation Committee

ETC Bulletin 25-001: Retrofitted Hot/Cold Beverage Kits - 2025 Field Season

Date: April 16, 2025
Questions?  Please contact:
Equipment Technology Committee

Due to spout failures and the associated risk of burn injuries, manufacturers have retrofitted the Hot/Cold Beverage Kits using a heat-shrinking band to secure the black spout at the insertion site. The updated kits feature a fluorescent label on each full kit assembly for easy identification. Catering units are encouraged to confirm the clear heat-shrinking bands are intact around each spout before filling.

ETC Bulletin 24-001 regarding Hot/Cold Beverage Kits has been archived and replaced by ETC Bulletin 25-001 for the 2025 season.

References:

NWCG Alerts

ETC-EB-25-001 Retrofitted Hot/Cold Beverage Kits

NWCG Standards for Wildland Fire Chainsaw Operations, PMS 212, and Next Generation Position Task Book for Basic Faller Are Now Available

Date: April 14, 2025
Questions?  Please contact:
Hazard Tree and Tree Felling Subcommittee

The updated NWCG Standards for Wildland Fire Chainsaw Operations, PMS 212, and NWCG Position Task Book for Basic Faller (FAL3), PMS 311-19 are now available.

The NWCG Standards for Wildland Fire Chainsaw Operations, PMS 212 includes position standards designed to be used in conjunction with the Next Generation Position Task Book (Next Gen PTB). The Next Gen PTB for Basic Faller (FAL3) includes an evaluation guide with suggested rating elements to consider when assessing trainees.

References:

NWCG Standards For Wildland Fire Chainsaw Operations, PMS 212

NWCG Position Task Book for Basic Faller (FAL3), PMS 311-119

NWCG Basic Faller (FAL3)

RMC Memo 25-01: Summary of Updates to Safety Officer Positions

Date: April 9, 2025
Questions?  Please contact:
RMC Member Eric Fransted

The Risk Management Committee (RMC) serves as the position steward for all Safety Officer incident positions and continues to improve position standards, training, and naming conventions. The implementation of Complex Incident Management (CIM) required changes to position titles. RMC collaborated with the NWCG Incident Position Standards Committee (IPSC) to propose and implement these updates. 

References:

RMC Memo 25-01: Summary of Updates to Safety Officer Positions 

NWCG Position Catalog